xxKuchipatchixx
Well-known member
Have you ever lost a battery cover for your tamagotchi. Now your upset because Its exposed to the elements more. Well as This replacement part isn't a total fix but It will hold the cover on and it will stay. Okay Now for what you'll need:
Gift Card(Preferably to a place you like, and you might want it to be the same color as your tamagotchi)
Scissors
Permenent Marker
loose velcrow(Or a screw)
screw driver(only if you replace velcrow with the screw)
Warning you might want to get a couple of these its not easy.
Okay Now I'm gonna tell you how to get started.(Now mine is alreaady done so I am going to show you how to do it but I'm not exactly gonna do it myself, however do do get pictures of mine at the end.Also if you dont have screws or velcrow this cover will still stay on by itself for a while, not too long though.)
1. Take the gift card and find an area of it that would look coolest on your tamagotchi.
2. Next hold the end of the gift card up to your tamagotchi and draw lines where the end of the cover would go.
3. Now cut down these line al the way to the end remember you can always cut more but not less if you feel you have to cut over a little bit more. Now If you want indentations on the side lower(Especially if your not using velcrow Cut off more than needed)
4. Cut along the lines so it dooesn't stick out of your tamagotchi too much.
5. Next its time to cut the tabs if your not msking these tabs skip to next step otherwise refer to picture.(tip use the marker to know where the tabs are) just cutt a centimeter off where the tabs need to be and there you go two tabs.
6. Next Stick the velcrow accodring to the picture and your done.(Now for the screw I have no picture because I have not tried it but use the marker to find out where the screw hole is make a hole there and screw in the screw)
voila enjoy your new back
Gift Card(Preferably to a place you like, and you might want it to be the same color as your tamagotchi)
Scissors
Permenent Marker
loose velcrow(Or a screw)
screw driver(only if you replace velcrow with the screw)
Warning you might want to get a couple of these its not easy.
Okay Now I'm gonna tell you how to get started.(Now mine is alreaady done so I am going to show you how to do it but I'm not exactly gonna do it myself, however do do get pictures of mine at the end.Also if you dont have screws or velcrow this cover will still stay on by itself for a while, not too long though.)
1. Take the gift card and find an area of it that would look coolest on your tamagotchi.
2. Next hold the end of the gift card up to your tamagotchi and draw lines where the end of the cover would go.
3. Now cut down these line al the way to the end remember you can always cut more but not less if you feel you have to cut over a little bit more. Now If you want indentations on the side lower(Especially if your not using velcrow Cut off more than needed)
4. Cut along the lines so it dooesn't stick out of your tamagotchi too much.
5. Next its time to cut the tabs if your not msking these tabs skip to next step otherwise refer to picture.(tip use the marker to know where the tabs are) just cutt a centimeter off where the tabs need to be and there you go two tabs.
6. Next Stick the velcrow accodring to the picture and your done.(Now for the screw I have no picture because I have not tried it but use the marker to find out where the screw hole is make a hole there and screw in the screw)
voila enjoy your new back
![Synvy [4 Pack] Anti Blue Light Screen Protector, Compatible with BANDAI Tamagotchi m! X (Tamagotchi Mikusu) series TPU Film Protectors [Not Tempered Glass]](https://m.media-amazon.com/images/I/51CglSJkaKL._SL500_.jpg)
